Re: error 80070424 windows update VISTA

I stumbled onto this thread while also trying to find a solution to "getting
Windows Updates on Vista... and getting error code 80070490". I tried your
fix with the:

net stop wuauserv
regsvr32 wuapi.dll
regsvr32 wuaueng.dll
regsvr32 wucltux.dll
regsvr32 wudriver.dll
regsvr32 wups2.dll
regsvr32 wups.dll
regsvr32 wuwebv.dll
net start wuauserv
exit

Unfortunately it didn't work, but while doing it, I did get an error saying
"The module "wudriver.dll" was loaded but the entry-point DllRegisterServer
was not found. Make sure the that "wudriver.dll" is a valid DLL or OCX file
and then try again. Does this have anything to do with it? Any other ideas?
I use Windows Live OneCare. My last good update was two weeks ago, and it
does not show me any restore points before that date.

Any help would be appreciated.


"MowGreen [MVP]" wrote:

> IF SubInACL works with Vista then why is it erring on the reg subkey you
> previously posted ?
> NOTE: Vista is not installed here and no such subkey to check
>
> I'll start with the last error code and work back up in the log:
>
> 0x80070490 E_PROP_ID_UNSUPPORTED
> Permission denied / [Problem initializing or using session variables] or
> Element not found
>
> 0x80244004 SUS_E_PT_SOAPCLIENT_CONNECT
> failed connecting to server
>
> 0x80072ef1 ERROR_INTERNET_OPERATION_CANCELLED
>
> 0x8024000c SUS_E_NOOP
> no operation is needed
>
> The last 3 errors were resolved. This one is what's preventing *some*
> updates from being offered :
>
> 2007-09-18 19:10:24:294 1048 980 Handler FATAL: UH: 0x80070490:
> EvaluateApplicability failed in CCbs::EvaluateApplicability
> 2007-09-18 19:10:24:295 1048 980 Setup WARNING: CBS EvaluateApplicability
> returned error, error = 0x80070490
> 2007-09-18 19:10:24:295 1048 980 Setup FATAL: Applicability evaluation
> for setup package
> "WUClient-SelfUpdate-ActiveX~31bf3856ad364e35~x86~~7.0.6000.381" failed,
> error = 0x80070490
>
> I don't *think* it's an ACL issue, rather, it's a communication issue
> due to some files not being registered properly.
> > Element not found
>
> Open an *Elevated* Command Prompt by right clicking cmd and choosing
> 'Run as administrator', stop the WU Service, and then register these
> files pressing Enter after each command
> NOTE: The net stop command may not be applicable in Vista. If so, then
> do this first:
> > To stop the Windows Update service
> >
> > You must be logged on as an administrator to perform these steps.
> > 1. Open Administrative Tools by clicking the Start button, clicking Control Panel,
> > clicking System and Maintenance, and then clicking Administrative Tools.
> > 2. Double-click Services. If you are prompted for an administrator password or
> > confirmation, type the password or provide confirmation.
> > 3. Right-click the Windows Update service, and then click Stop.
>
> net stop wuauserv
> regsvr32 wuapi.dll
> regsvr32 wuaueng.dll
> regsvr32 wucltux.dll
> regsvr32 wudriver.dll
> regsvr32 wups2.dll
> regsvr32 wups.dll
> regsvr32 wuwebv.dll
> net start wuauserv
> exit
>
> Restart the system and see if it can update now.
>
>
> MowGreen [MVP 2003-2007]
> ===============
> *-343-* FDNY
> Never Forgotten
> ===============
>
>
> wirelessguru wrote:
>
> > Actually, SubInACL DOES work in Vista - at least it appears to do something.
> > I had tried that due to the information posted in this topic
> > http://www.microsoft.com/communities...f64f9a0012&p=1
> >
> > I found the present topic by typing "windows update agent installer
> > encountered
> > unrecoverable error" into Google - which is the error I got when I tried to
> > install it.
> >
> > My 1166 KB log file only goes back to Sept. 6. Here are the log file lines
> > from this evening turning on the computer, then manually checking for
> > updates about 18 minutes later...
> >
> > 2007-09-18 19:09:40:506 1048 9a8 AU AU deferring detection until wake-up
> > from hibernation
> > 2007-09-18 19:09:42:980 1048 a20 Report WARNING: Reporter failed to upload
> > events with hr = 8024000c.
> > 2007-09-18 19:09:42:981 1048 a20 Report WARNING: Reporter failed to upload
> > events with hr = 8024000c.
> > 2007-09-18 19:09:45:816 1048 9a8 AU Triggering Online detection
> > (non-interactive)
> > 2007-09-18 19:09:48:216 1048 5d0 Report Uploading 4 events using cached
> > cookie, reporting URL =
> > http://stats.update.microsoft.com/Re...ebService.asmx
> > 2007-09-18 19:09:48:238 1048 5d0 Report WARNING: Failed to upload events to
> > the server with hr = 80072ef1.
> > 2007-09-18 19:09:48:238 1048 5d0 PT WARNING: ReportEventBatch failure, error
> > = 0x80244004, soap client error = 4, soap error code = 0, HTTP status code =
> > 200
> > 2007-09-18 19:09:48:238 1048 5d0 Report WARNING: Reporter failed to upload
> > events with hr = 80244004.
> > 2007-09-18 19:09:48:258 1048 5d0 Report Uploading 4 events using cached
> > cookie, reporting URL =
> > http://stats.update.microsoft.com/Re...ebService.asmx
> > 2007-09-18 19:09:51:626 1048 5d0 Report Reporter successfully uploaded 4
> > events.
> > 2007-09-18 19:10:15:833 1048 9a8 AU #############
> > 2007-09-18 19:10:15:833 1048 9a8 AU ## START ## AU: Search for updates
> > 2007-09-18 19:10:15:833 1048 9a8 AU #########
> > 2007-09-18 19:10:16:497 1048 9a8 AU <<## SUBMITTED ## AU: Search for updates
> > [CallId = {14C577DC-52BF-401C-863E-86EE36907175}]
> > 2007-09-18 19:10:16:497 1048 980 Agent *************
> > 2007-09-18 19:10:16:497 1048 980 Agent ** START ** Agent: Finding updates
> > [CallerId = AutomaticUpdates]
> > 2007-09-18 19:10:16:497 1048 980 Agent *********
> > 2007-09-18 19:10:16:497 1048 980 Setup Checking for agent SelfUpdate
> > 2007-09-18 19:10:16:733 1048 980 Setup Client version: Core: 6.0.6000.16386
> > Aux: 6.0.6000.16386
> > 2007-09-18 19:10:22:567 1048 980 Setup Determining whether a new setup
> > handler needs to be downloaded
> > 2007-09-18 19:10:22:567 1048 980 Setup SelfUpdate handler is not found. It
> > will be downloaded
> > 2007-09-18 19:10:22:586 1048 980 Setup Evaluating applicability of setup
> > package "WUClient-SelfUpdate-ActiveX~31bf3856ad364e35~x86~~7.0.6000.381"
> > 2007-09-18 19:10:24:294 1048 980 Handler FATAL: UH: 0x80070490:
> > EvaluateApplicability failed in CCbs::EvaluateApplicability
> > 2007-09-18 19:10:24:295 1048 980 Setup WARNING: CBS EvaluateApplicability
> > returned error, error = 0x80070490
> > 2007-09-18 19:10:24:295 1048 980 Setup FATAL: Applicability evaluation for
> > setup package
> > "WUClient-SelfUpdate-ActiveX~31bf3856ad364e35~x86~~7.0.6000.381" failed,
> > error = 0x80070490
> > 2007-09-18 19:10:24:296 1048 980 Setup FATAL: SelfUpdate check failed, err =
> > 0x80070490
> > 2007-09-18 19:10:24:296 1048 980 Agent * WARNING: Skipping scan,
> > self-update check returned 0x80070490
> > 2007-09-18 19:10:24:438 1048 980 Agent * WARNING: Exit code = 0x80070490
> > 2007-09-18 19:10:24:438 1048 980 Agent *********
> > 2007-09-18 19:10:24:438 1048 980 Agent ** END ** Agent: Finding updates
> > [CallerId = AutomaticUpdates]
> > 2007-09-18 19:10:24:438 1048 980 Agent *************
> > 2007-09-18 19:10:24:439 1048 980 Agent WARNING: WU client failed Searching
> > for update with error 0x80070490
> > 2007-09-18 19:10:24:439 1048 ff4 AU >>## RESUMED ## AU: Search for updates
> > [CallId = {14C577DC-52BF-401C-863E-86EE36907175}]
> > 2007-09-18 19:10:24:439 1048 ff4 AU # WARNING: Search callback failed,
> > result = 0x80070490
> > 2007-09-18 19:10:24:439 1048 ff4 AU # WARNING: Failed to find updates with
> > error code 80070490
> > 2007-09-18 19:10:24:439 1048 ff4 AU #########
> > 2007-09-18 19:10:24:439 1048 ff4 AU ## END ## AU: Search for updates
> > [CallId = {14C577DC-52BF-401C-863E-86EE36907175}]
> > 2007-09-18 19:10:24:439 1048 ff4 AU #############
> > 2007-09-18 19:10:24:440 1048 ff4 AU AU setting next detection timeout to
> > 2007-09-19 07:10:24
> > 2007-09-18 19:10:24:440 1048 ff4 AU Setting AU scheduled install time to
> > 2007-09-19 10:00:00
> > 2007-09-18 19:10:29:368 1048 a68 Report REPORT EVENT:
> > {4A15B70F-1FEE-4BE2-8EDB-EA9049EA7BBC} 2007-09-18
> > 19:10:24:296-0700 1 148 101 {61CA813A-7585-442E-A66B-B0D15CE6BDC0} 1 80070490 SelfUpdate Failure Software
> > Synchronization Windows Update Client failed to detect with error 0x80070490.
> > 2007-09-18 19:38:20:006 1048 830 AU Triggering AU detection through
> > DetectNow API
> > 2007-09-18 19:38:20:007 1048 830 AU Triggering Online detection (interactive)
> > 2007-09-18 19:38:20:015 1048 9a8 AU #############
> > 2007-09-18 19:38:20:023 1048 9a8 AU ## START ## AU: Search for updates
> > 2007-09-18 19:38:20:023 1048 9a8 AU #########
> > 2007-09-18 19:38:20:097 1048 9a8 AU <<## SUBMITTED ## AU: Search for updates
> > [CallId = {28A5A840-BBBE-4F26-9EE7-57C67DE2C615}]
> > 2007-09-18 19:38:20:097 1048 cdc Agent *************
> > 2007-09-18 19:38:20:097 1048 cdc Agent ** START ** Agent: Finding updates
> > [CallerId = AutomaticUpdates]
> > 2007-09-18 19:38:20:097 1048 cdc Agent *********
> > 2007-09-18 19:38:20:097 1048 cdc Setup Checking for agent SelfUpdate
> > 2007-09-18 19:38:20:098 1048 cdc Setup Client version: Core: 6.0.6000.16386
> > Aux: 6.0.6000.16386
> > 2007-09-18 19:38:21:224 1048 cdc Setup Determining whether a new setup
> > handler needs to be downloaded
> > 2007-09-18 19:38:21:224 1048 cdc Setup SelfUpdate handler is not found. It
> > will be downloaded
> > 2007-09-18 19:38:21:225 1048 cdc Setup Evaluating applicability of setup
> > package "WUClient-SelfUpdate-ActiveX~31bf3856ad364e35~x86~~7.0.6000.381"
> > 2007-09-18 19:38:21:506 1048 cdc Handler FATAL: UH: 0x80070490:
> > EvaluateApplicability failed in CCbs::EvaluateApplicability
> > 2007-09-18 19:38:21:507 1048 cdc Setup WARNING: CBS EvaluateApplicability
> > returned error, error = 0x80070490
> > 2007-09-18 19:38:21:508 1048 cdc Setup FATAL: Applicability evaluation for
> > setup package
> > "WUClient-SelfUpdate-ActiveX~31bf3856ad364e35~x86~~7.0.6000.381" failed,
> > error = 0x80070490
> > 2007-09-18 19:38:21:508 1048 cdc Setup FATAL: SelfUpdate check failed, err =
> > 0x80070490
> > 2007-09-18 19:38:21:508 1048 cdc Agent * WARNING: Skipping scan,
> > self-update check returned 0x80070490
> > 2007-09-18 19:38:21:596 1048 cdc Agent * WARNING: Exit code = 0x80070490
> > 2007-09-18 19:38:21:596 1048 cdc Agent *********
> > 2007-09-18 19:38:21:596 1048 cdc Agent ** END ** Agent: Finding updates
> > [CallerId = AutomaticUpdates]
> > 2007-09-18 19:38:21:596 1048 cdc Agent *************
> > 2007-09-18 19:38:21:596 1048 cdc Agent WARNING: WU client failed Searching
> > for update with error 0x80070490
> > 2007-09-18 19:38:21:596 1048 5dc AU >>## RESUMED ## AU: Search for updates
> > [CallId = {28A5A840-BBBE-4F26-9EE7-57C67DE2C615}]
> > 2007-09-18 19:38:21:596 1048 5dc AU # WARNING: Search callback failed,
> > result = 0x80070490
> > 2007-09-18 19:38:21:596 1048 5dc AU # WARNING: Failed to find updates with
> > error code 80070490
> > 2007-09-18 19:38:21:596 1048 5dc AU #########
> > 2007-09-18 19:38:21:597 1048 5dc AU ## END ## AU: Search for updates
> > [CallId = {28A5A840-BBBE-4F26-9EE7-57C67DE2C615}]
> > 2007-09-18 19:38:21:597 1048 5dc AU #############
> > 2007-09-18 19:38:21:597 1048 5dc AU AU setting next detection timeout to
> > 2007-09-19 07:38:21
> > 2007-09-18 19:38:21:597 1048 5dc AU Setting AU scheduled install time to
> > 2007-09-19 10:00:00
> > 2007-09-18 19:38:26:534 1048 5dc Report REPORT EVENT:
> > {90D60600-9548-464A-B630-1411459B5151} 2007-09-18
> > 19:38:21:508-0700 1 148 101 {61CA813A-7585-442E-A66B-B0D15CE6BDC0} 1 80070490 SelfUpdate Failure Software
> > Synchronization Windows Update Client failed to detect with error 0x80070490.
> >
> >
> >
> >
> > "MowGreen [MVP]" wrote:
> >
> >
> >>Ouch. I doubt whether SubInACL works in Vista.
> >>Could you please post a section of the WindowsUpdate.log by going to
> >>Start > Run > type in
> >>
> >>%windir%\windowsupdate.log
> >>Click OK
> >>
> >>If possible, locate a section of the log from around 3/20/07.
> >>If not, start at the bottom and work your way up to a section that shows
> >>an ERROR, WARNING, or FATAL. Then copy&paste that along with 30 or so
> >>*preceding* lines into your reply, please.
> >>
> >>MowGreen [MVP 2003-2007]
> >>===============
> >> *-343-* FDNY
> >>Never Forgotten
> >>===============
> >>
> >>
> >>wirelessguru wrote:
> >>
> >>
> >>>After reading this conversation and the attempted fixes, I am having similar
> >>>difficulty getting Windows Updates on Vista except I am getting error code
> >>>80070490. When trying the fixes, I am also running into the same error
> >>>messages. Here's a few more details that will hopefully help resolve this
> >>>problem for myself and others (hopefully without having to reinstall)...
> >>>
> >>>1. Only running AVG Anti-Virus
> >>>2. The Subinacl tool errors on
> >>>HKLM\Software\Microsoft\WindowsNT\CurrentVersio n\Permissions or a subkey of
> >>>that (the DOS window is not wide enough to see the full key)
> >>>3. Windows Update history shows that all Microsoft Updates (Office, Windows
> >>>Defender, and Malicious Software Removal Tool) ARE being downloaded and
> >>>installed automatically.
> >>>4. Last Recommended Update was on 3/20/07 - KB932246 "Failed"
> >>>5. The last successful update was on 2/27/07 - KB929685 "Successful"
> >>>6. Control Panel > Programs and Features > Installed Updates shows "No
> >>>updates are installed on this computer"
> >>>
> >>>Hopefully this helps get this problem resolved.
> >>>
> >>>
> >>>"MowGreen [MVP]" wrote:
> >>>
> >>>
> >>>
> >>>>getalexfr wrote:
> >>>>
> >>>>
> >>>>
> >>>>>the commands you gave me to put into cmd all worked fine apart from one:
> >>>>>regsvr32 wudriver.dll
> >>>>>to this i have a regsvr32 window pop up saying >>
> >>>>>
> >>>>>The module "wudriver.dll" was loaded but the entry-point
> >>>>>DllRegisterServer was not found.
> >>>>>
> >>>>>Make sure that "wudriver.dll" is a valid DLL or OCX file and then try
> >>>>>again.
> >>>>>
> >>>>><<
> >>>>>
> >>>>>
> >>>>>wuwebv.dll is version 7.0.600.374
> >>>>>
> >>>>>thanks for all your help. i've now got hold of a microsoft support team
> >>>>>guy who is trying to help me too, by email. will post any results here,
> >>>>>but i fear it could take some time!
> >>>>>a
> >>>>>
> >>>>>
> >>>>

"notaguru" <notaguru@discussions.microsoft.com> wrote in message news:7D871F12-7725-494D-8B4E-623CAEABBC27@microsoft.com...
>I stumbled onto this thread while also trying to find a solution to "getting
> Windows Updates on Vista... and getting error code 80070490". I tried your
> fix with the:
>
> net stop wuauserv
> regsvr32 wuapi.dll
> regsvr32 wuaueng.dll
> regsvr32 wucltux.dll
> regsvr32 wudriver.dll
> regsvr32 wups2.dll
> regsvr32 wups.dll
> regsvr32 wuwebv.dll
> net start wuauserv
> exit
>
> Unfortunately it didn't work, but while doing it, I did get an error saying
> "The module "wudriver.dll" was loaded but the entry-point DllRegisterServer
> was not found. Make sure the that "wudriver.dll" is a valid DLL or OCX file
> and then try again. Does this have anything to do with it?


> Any other ideas?


Try some diagnosis? Note that the error code may be represented
elsewhere by the decimal equivalent of its last half...

<cmd_output OS="XPsp3">
E:\>set /a c = 0x490
1168
E:\>net helpmsg %c%

Element not found.
</cmd_output>


So try searching all the files that the update created or modified
for either that value or just the hex characters.

Also, I would try searching with just 490 (i.e., without the 0x prefix
which specifies that the characters are to be interpreted as hex
instead of decimal) because some log messages don't always include
that and in any case including it would preclude you from finding potentially
useful context where the equivalent value was reported with leading zeros.


> I use Windows Live OneCare. My last good update was two weeks ago, and it
> does not show me any restore points before that date.
>
> Any help would be appreciated.


Good luck

Robert Aldwinckle
---


>
>
> "MowGreen [MVP]" wrote:
>
>> IF SubInACL works with Vista then why is it erring on the reg subkey you
>> previously posted ?
>> NOTE: Vista is not installed here and no such subkey to check
>>
>> I'll start with the last error code and work back up in the log:
>>
>> 0x80070490 E_PROP_ID_UNSUPPORTED
>> Permission denied / [Problem initializing or using session variables] or
>> Element not found
>>
>> 0x80244004 SUS_E_PT_SOAPCLIENT_CONNECT
>> failed connecting to server
>>
>> 0x80072ef1 ERROR_INTERNET_OPERATION_CANCELLED
>>
>> 0x8024000c SUS_E_NOOP
>> no operation is needed
>>
>> The last 3 errors were resolved. This one is what's preventing *some*
>> updates from being offered :
>>
>> 2007-09-18 19:10:24:294 1048 980 Handler FATAL: UH: 0x80070490:
>> EvaluateApplicability failed in CCbs::EvaluateApplicability
>> 2007-09-18 19:10:24:295 1048 980 Setup WARNING: CBS EvaluateApplicability
>> returned error, error = 0x80070490
>> 2007-09-18 19:10:24:295 1048 980 Setup FATAL: Applicability evaluation
>> for setup package
>> "WUClient-SelfUpdate-ActiveX~31bf3856ad364e35~x86~~7.0.6000.381" failed,
>> error = 0x80070490
>>
>> I don't *think* it's an ACL issue, rather, it's a communication issue
>> due to some files not being registered properly.
>> > Element not found
>>
>> Open an *Elevated* Command Prompt by right clicking cmd and choosing
>> 'Run as administrator', stop the WU Service, and then register these
>> files pressing Enter after each command
>> NOTE: The net stop command may not be applicable in Vista. If so, then
>> do this first:
>> > To stop the Windows Update service
>> >
>> > You must be logged on as an administrator to perform these steps.
>> > 1. Open Administrative Tools by clicking the Start button, clicking Control Panel,
>> > clicking System and Maintenance, and then clicking Administrative Tools.
>> > 2. Double-click Services. If you are prompted for an administrator password or
>> > confirmation, type the password or provide confirmation.
>> > 3. Right-click the Windows Update service, and then click Stop.
>>
>> net stop wuauserv
>> regsvr32 wuapi.dll
>> regsvr32 wuaueng.dll
>> regsvr32 wucltux.dll
>> regsvr32 wudriver.dll
>> regsvr32 wups2.dll
>> regsvr32 wups.dll
>> regsvr32 wuwebv.dll
>> net start wuauserv
>> exit
>>
>> Restart the system and see if it can update now.
>>
>>
>> MowGreen [MVP 2003-2007]
>> ===============
>> *-343-* FDNY
>> Never Forgotten
>> ===============
>>
>>
>> wirelessguru wrote:
>>
>> > Actually, SubInACL DOES work in Vista - at least it appears to do something.
>> > I had tried that due to the information posted in this topic
>> > http://www.microsoft.com/communities...f64f9a0012&p=1
>> >
>> > I found the present topic by typing "windows update agent installer
>> > encountered
>> > unrecoverable error" into Google - which is the error I got when I tried to
>> > install it.
>> >
>> > My 1166 KB log file only goes back to Sept. 6. Here are the log file lines
>> > from this evening turning on the computer, then manually checking for
>> > updates about 18 minutes later...
>> >
>> > 2007-09-18 19:09:40:506 1048 9a8 AU AU deferring detection until wake-up
>> > from hibernation
>> > 2007-09-18 19:09:42:980 1048 a20 Report WARNING: Reporter failed to upload
>> > events with hr = 8024000c.
>> > 2007-09-18 19:09:42:981 1048 a20 Report WARNING: Reporter failed to upload
>> > events with hr = 8024000c.
>> > 2007-09-18 19:09:45:816 1048 9a8 AU Triggering Online detection
>> > (non-interactive)
>> > 2007-09-18 19:09:48:216 1048 5d0 Report Uploading 4 events using cached
>> > cookie, reporting URL =
>> > http://stats.update.microsoft.com/Re...ebService.asmx
>> > 2007-09-18 19:09:48:238 1048 5d0 Report WARNING: Failed to upload events to
>> > the server with hr = 80072ef1.
>> > 2007-09-18 19:09:48:238 1048 5d0 PT WARNING: ReportEventBatch failure, error
>> > = 0x80244004, soap client error = 4, soap error code = 0, HTTP status code =
>> > 200
>> > 2007-09-18 19:09:48:238 1048 5d0 Report WARNING: Reporter failed to upload
>> > events with hr = 80244004.
>> > 2007-09-18 19:09:48:258 1048 5d0 Report Uploading 4 events using cached
>> > cookie, reporting URL =
>> > http://stats.update.microsoft.com/Re...ebService.asmx
>> > 2007-09-18 19:09:51:626 1048 5d0 Report Reporter successfully uploaded 4
>> > events.
>> > 2007-09-18 19:10:15:833 1048 9a8 AU #############
>> > 2007-09-18 19:10:15:833 1048 9a8 AU ## START ## AU: Search for updates
>> > 2007-09-18 19:10:15:833 1048 9a8 AU #########
>> > 2007-09-18 19:10:16:497 1048 9a8 AU <<## SUBMITTED ## AU: Search for updates
>> > [CallId = {14C577DC-52BF-401C-863E-86EE36907175}]
>> > 2007-09-18 19:10:16:497 1048 980 Agent *************
>> > 2007-09-18 19:10:16:497 1048 980 Agent ** START ** Agent: Finding updates
>> > [CallerId = AutomaticUpdates]
>> > 2007-09-18 19:10:16:497 1048 980 Agent *********
>> > 2007-09-18 19:10:16:497 1048 980 Setup Checking for agent SelfUpdate
>> > 2007-09-18 19:10:16:733 1048 980 Setup Client version: Core: 6.0.6000.16386
>> > Aux: 6.0.6000.16386
>> > 2007-09-18 19:10:22:567 1048 980 Setup Determining whether a new setup
>> > handler needs to be downloaded
>> > 2007-09-18 19:10:22:567 1048 980 Setup SelfUpdate handler is not found. It
>> > will be downloaded
>> > 2007-09-18 19:10:22:586 1048 980 Setup Evaluating applicability of setup
>> > package "WUClient-SelfUpdate-ActiveX~31bf3856ad364e35~x86~~7.0.6000.381"
>> > 2007-09-18 19:10:24:294 1048 980 Handler FATAL: UH: 0x80070490:
>> > EvaluateApplicability failed in CCbs::EvaluateApplicability
>> > 2007-09-18 19:10:24:295 1048 980 Setup WARNING: CBS EvaluateApplicability
>> > returned error, error = 0x80070490
>> > 2007-09-18 19:10:24:295 1048 980 Setup FATAL: Applicability evaluation for
>> > setup package
>> > "WUClient-SelfUpdate-ActiveX~31bf3856ad364e35~x86~~7.0.6000.381" failed,
>> > error = 0x80070490
>> > 2007-09-18 19:10:24:296 1048 980 Setup FATAL: SelfUpdate check failed, err =
>> > 0x80070490
>> > 2007-09-18 19:10:24:296 1048 980 Agent * WARNING: Skipping scan,
>> > self-update check returned 0x80070490
>> > 2007-09-18 19:10:24:438 1048 980 Agent * WARNING: Exit code = 0x80070490
>> > 2007-09-18 19:10:24:438 1048 980 Agent *********
>> > 2007-09-18 19:10:24:438 1048 980 Agent ** END ** Agent: Finding updates
>> > [CallerId = AutomaticUpdates]
>> > 2007-09-18 19:10:24:438 1048 980 Agent *************
>> > 2007-09-18 19:10:24:439 1048 980 Agent WARNING: WU client failed Searching
>> > for update with error 0x80070490
>> > 2007-09-18 19:10:24:439 1048 ff4 AU >>## RESUMED ## AU: Search for updates
>> > [CallId = {14C577DC-52BF-401C-863E-86EE36907175}]
>> > 2007-09-18 19:10:24:439 1048 ff4 AU # WARNING: Search callback failed,
>> > result = 0x80070490
>> > 2007-09-18 19:10:24:439 1048 ff4 AU # WARNING: Failed to find updates with
>> > error code 80070490
>> > 2007-09-18 19:10:24:439 1048 ff4 AU #########
>> > 2007-09-18 19:10:24:439 1048 ff4 AU ## END ## AU: Search for updates
>> > [CallId = {14C577DC-52BF-401C-863E-86EE36907175}]
>> > 2007-09-18 19:10:24:439 1048 ff4 AU #############
>> > 2007-09-18 19:10:24:440 1048 ff4 AU AU setting next detection timeout to
>> > 2007-09-19 07:10:24
>> > 2007-09-18 19:10:24:440 1048 ff4 AU Setting AU scheduled install time to
>> > 2007-09-19 10:00:00
>> > 2007-09-18 19:10:29:368 1048 a68 Report REPORT EVENT:
>> > {4A15B70F-1FEE-4BE2-8EDB-EA9049EA7BBC} 2007-09-18
>> > 19:10:24:296-0700 1 148 101 {61CA813A-7585-442E-A66B-B0D15CE6BDC0} 1 80070490 SelfUpdate Failure Software
>> > Synchronization Windows Update Client failed to detect with error 0x80070490.
>> > 2007-09-18 19:38:20:006 1048 830 AU Triggering AU detection through
>> > DetectNow API
>> > 2007-09-18 19:38:20:007 1048 830 AU Triggering Online detection (interactive)
>> > 2007-09-18 19:38:20:015 1048 9a8 AU #############
>> > 2007-09-18 19:38:20:023 1048 9a8 AU ## START ## AU: Search for updates
>> > 2007-09-18 19:38:20:023 1048 9a8 AU #########
>> > 2007-09-18 19:38:20:097 1048 9a8 AU <<## SUBMITTED ## AU: Search for updates
>> > [CallId = {28A5A840-BBBE-4F26-9EE7-57C67DE2C615}]
>> > 2007-09-18 19:38:20:097 1048 cdc Agent *************
>> > 2007-09-18 19:38:20:097 1048 cdc Agent ** START ** Agent: Finding updates
>> > [CallerId = AutomaticUpdates]
>> > 2007-09-18 19:38:20:097 1048 cdc Agent *********
>> > 2007-09-18 19:38:20:097 1048 cdc Setup Checking for agent SelfUpdate
>> > 2007-09-18 19:38:20:098 1048 cdc Setup Client version: Core: 6.0.6000.16386
>> > Aux: 6.0.6000.16386
>> > 2007-09-18 19:38:21:224 1048 cdc Setup Determining whether a new setup
>> > handler needs to be downloaded
>> > 2007-09-18 19:38:21:224 1048 cdc Setup SelfUpdate handler is not found. It
>> > will be downloaded
>> > 2007-09-18 19:38:21:225 1048 cdc Setup Evaluating applicability of setup
>> > package "WUClient-SelfUpdate-ActiveX~31bf3856ad364e35~x86~~7.0.6000.381"
>> > 2007-09-18 19:38:21:506 1048 cdc Handler FATAL: UH: 0x80070490:
>> > EvaluateApplicability failed in CCbs::EvaluateApplicability
>> > 2007-09-18 19:38:21:507 1048 cdc Setup WARNING: CBS EvaluateApplicability
>> > returned error, error = 0x80070490
>> > 2007-09-18 19:38:21:508 1048 cdc Setup FATAL: Applicability evaluation for
>> > setup package
>> > "WUClient-SelfUpdate-ActiveX~31bf3856ad364e35~x86~~7.0.6000.381" failed,
>> > error = 0x80070490
>> > 2007-09-18 19:38:21:508 1048 cdc Setup FATAL: SelfUpdate check failed, err =
>> > 0x80070490
>> > 2007-09-18 19:38:21:508 1048 cdc Agent * WARNING: Skipping scan,
>> > self-update check returned 0x80070490
>> > 2007-09-18 19:38:21:596 1048 cdc Agent * WARNING: Exit code = 0x80070490
>> > 2007-09-18 19:38:21:596 1048 cdc Agent *********
>> > 2007-09-18 19:38:21:596 1048 cdc Agent ** END ** Agent: Finding updates
>> > [CallerId = AutomaticUpdates]
>> > 2007-09-18 19:38:21:596 1048 cdc Agent *************
>> > 2007-09-18 19:38:21:596 1048 cdc Agent WARNING: WU client failed Searching
>> > for update with error 0x80070490
>> > 2007-09-18 19:38:21:596 1048 5dc AU >>## RESUMED ## AU: Search for updates
>> > [CallId = {28A5A840-BBBE-4F26-9EE7-57C67DE2C615}]
>> > 2007-09-18 19:38:21:596 1048 5dc AU # WARNING: Search callback failed,
>> > result = 0x80070490
>> > 2007-09-18 19:38:21:596 1048 5dc AU # WARNING: Failed to find updates with
>> > error code 80070490
>> > 2007-09-18 19:38:21:596 1048 5dc AU #########
>> > 2007-09-18 19:38:21:597 1048 5dc AU ## END ## AU: Search for updates
>> > [CallId = {28A5A840-BBBE-4F26-9EE7-57C67DE2C615}]
>> > 2007-09-18 19:38:21:597 1048 5dc AU #############
>> > 2007-09-18 19:38:21:597 1048 5dc AU AU setting next detection timeout to
>> > 2007-09-19 07:38:21
>> > 2007-09-18 19:38:21:597 1048 5dc AU Setting AU scheduled install time to
>> > 2007-09-19 10:00:00
>> > 2007-09-18 19:38:26:534 1048 5dc Report REPORT EVENT:
>> > {90D60600-9548-464A-B630-1411459B5151} 2007-09-18
>> > 19:38:21:508-0700 1 148 101 {61CA813A-7585-442E-A66B-B0D15CE6BDC0} 1 80070490 SelfUpdate Failure Software
>> > Synchronization Windows Update Client failed to detect with error 0x80070490.
>> >
>> >
>> >
>> >
>> > "MowGreen [MVP]" wrote:
>> >
>> >
>> >>Ouch. I doubt whether SubInACL works in Vista.
>> >>Could you please post a section of the WindowsUpdate.log by going to
>> >>Start > Run > type in
>> >>
>> >>%windir%\windowsupdate.log
>> >>Click OK
>> >>
>> >>If possible, locate a section of the log from around 3/20/07.
>> >>If not, start at the bottom and work your way up to a section that shows
>> >>an ERROR, WARNING, or FATAL. Then copy&paste that along with 30 or so
>> >>*preceding* lines into your reply, please.
>> >>
>> >>MowGreen [MVP 2003-2007]
>> >>===============
>> >> *-343-* FDNY
>> >>Never Forgotten
>> >>===============
>> >>
>> >>
>> >>wirelessguru wrote:
>> >>
>> >>
>> >>>After reading this conversation and the attempted fixes, I am having similar
>> >>>difficulty getting Windows Updates on Vista except I am getting error code
>> >>>80070490. When trying the fixes, I am also running into the same error
>> >>>messages. Here's a few more details that will hopefully help resolve this
>> >>>problem for myself and others (hopefully without having to reinstall)...
>> >>>
>> >>>1. Only running AVG Anti-Virus
>> >>>2. The Subinacl tool errors on
>> >>>HKLM\Software\Microsoft\WindowsNT\CurrentVersio n\Permissions or a subkey of
>> >>>that (the DOS window is not wide enough to see the full key)
>> >>>3. Windows Update history shows that all Microsoft Updates (Office, Windows
>> >>>Defender, and Malicious Software Removal Tool) ARE being downloaded and
>> >>>installed automatically.
>> >>>4. Last Recommended Update was on 3/20/07 - KB932246 "Failed"
>> >>>5. The last successful update was on 2/27/07 - KB929685 "Successful"
>> >>>6. Control Panel > Programs and Features > Installed Updates shows "No
>> >>>updates are installed on this computer"
>> >>>
>> >>>Hopefully this helps get this problem resolved.
>> >>>
>> >>>
>> >>>"MowGreen [MVP]" wrote:
>> >>>
>> >>>
>> >>>
>> >>>>getalexfr wrote:
>> >>>>
>> >>>>
>> >>>>
>> >>>>>the commands you gave me to put into cmd all worked fine apart from one:
>> >>>>>regsvr32 wudriver.dll
>> >>>>>to this i have a regsvr32 window pop up saying >>
>> >>>>>
>> >>>>>The module "wudriver.dll" was loaded but the entry-point
>> >>>>>DllRegisterServer was not found.
>> >>>>>
>> >>>>>Make sure that "wudriver.dll" is a valid DLL or OCX file and then try
>> >>>>>again.
>> >>>>>
>> >>>>><<
>> >>>>>
>> >>>>>
>> >>>>>wuwebv.dll is version 7.0.600.374
>> >>>>>
>> >>>>>thanks for all your help. i've now got hold of a microsoft support team
>> >>>>>guy who is trying to help me too, by email. will post any results here,
>> >>>>>but i fear it could take some time!
>> >>>>>a
>> >>>>>
>> >>>>>
>> >>>>

Hello,

I am having issues with the error code 80070424. I tried to register
the dlls as suggested above but when I get to the wudriver.dll it gives
me the message:
The module "wudriver.dll" was loaded but the entry-point
DllRegisterServer was not found.

Make sure that "wudriver.dll" is a valid DLL or OCX file and then try
again.

I have not found a fix for this and don't know where to turn now.

Please Help.

Thanks!!


--
Trig217
------------------------------------------------------------------------
Trig217's Profile: http://forums.techarena.in/members/trig217.htm
View this thread: http://forums.techarena.in/windows-update/814712.htm

http://forums.techarena.in

"Trig217" <Trig217.3on5fb@DoNotSpam.com> wrote in message news:Trig217.3on5fb@DoNotSpam.com...
>
> Hello,
>
> I am having issues with the error code 80070424. I tried to register
> the dlls as suggested above but when I get to the wudriver.dll it gives
> me the message:
> The module "wudriver.dll" was loaded but the entry-point
> DllRegisterServer was not found.
>
> Make sure that "wudriver.dll" is a valid DLL or OCX file and then try
> again.


FWIW I would suspect that wudriver.dll should not have
been included in those instructions. I just checked the one
that I have with DependencyWalker and found that it
would not be registerable.


>
> I have not found a fix for this and don't know where to turn now.


The meaning of the code isn't clear

<cmd_output OS="XPsp3">
E:\>set /a c = 0x424
1060
E:\>net helpmsg %c%

The specified service does not exist as an installed service.
</cmd_output>

So, *which* service is the "specified" service?

In case it's BITS you could use bitsadmin /util (in a cmd
window Run as... Administrator) to check or repair that service.


Good luck

Robert Aldwinckle
---


>
> Please Help.
>
> Thanks!!
>
>
> --
> Trig217
> ------------------------------------------------------------------------
> Trig217's Profile: http://forums.techarena.in/members/trig217.htm
> View this thread: http://forums.techarena.in/windows-update/814712.htm
>
> http://forums.techarena.in
>

I'm not having a problem with bits it seems that the service is working
fine. I'm still not sure what the problem is.

Robert Aldwinckle;4286070 Wrote:
> FWIW I would suspect that wudriver.dll should not have
> been included in those instructions. I just checked the one
> that I have with DependencyWalker and found that it
> would not be registerable.
>
>
> >
> > I have not found a fix for this and don't know where to turn now.
>
>
> The meaning of the code isn't clear
>
> <cmd_output OS="XPsp3">
> E:\>set /a c = 0x424
> 1060
> E:\>net helpmsg %c%
>
> The specified service does not exist as an installed service.
> </cmd_output>
>
> So, *which* service is the "specified" service?
>
> In case it's BITS you could use bitsadmin /util (in a cmd
> window Run as... Administrator) to check or repair that service.


--
Trig217
------------------------------------------------------------------------
Trig217's Profile: http://forums.techarena.in/members/trig217.htm
View this thread: http://forums.techarena.in/windows-update/814712.htm

http://forums.techarena.in

"Trig217" <Trig217.3osmnb@DoNotSpam.com> wrote in message news:Trig217.3osmnb@DoNotSpam.com...
>

> I'm not having a problem with bits it seems that the service is working
> fine. I'm still not sure what the problem is.


Then you will have to use your logs to figure out
which service the error is referring to. Use ProcMon
to supplement whatever diagnostics you are getting
if necessary when you retry.

Alternatively, since it is probably still something happening
in the download phase you could download whatever update
it is manually and install it manually, thus bypassing whatever
problems you are having with AU/WU/MU. Then you could
request help from a newsgroup which specializes in whatever
product the update involves. Etc.


Good luck

Robert
---


>
> Robert Aldwinckle;4286070 Wrote:
>> FWIW I would suspect that wudriver.dll should not have
>> been included in those instructions. I just checked the one
>> that I have with DependencyWalker and found that it
>> would not be registerable.
>>
>>
>> >
>> > I have not found a fix for this and don't know where to turn now.
>>
>>
>> The meaning of the code isn't clear
>>
>> <cmd_output OS="XPsp3">
>> E:\>set /a c = 0x424
>> 1060
>> E:\>net helpmsg %c%
>>
>> The specified service does not exist as an installed service.
>> </cmd_output>
>>
>> So, *which* service is the "specified" service?
>>
>> In case it's BITS you could use bitsadmin /util (in a cmd
>> window Run as... Administrator) to check or repair that service.
>
>
> --
> Trig217
> ------------------------------------------------------------------------
> Trig217's Profile: http://forums.techarena.in/members/trig217.htm
> View this thread: http://forums.techarena.in/windows-update/814712.htm
>
> http://forums.techarena.in
>

I have resolved similar problem on my Windows Vista Home Premium x64 sp1. The
problem was caused by the lack of TrustedInstaller service. I don't know why
and when this service has disappeared from my system but when I realized this
I restore it as follows:

1. Add to registry (save text below to temporary .reg file and import it in
regedit):

[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Servic es\TrustedInstaller]
"DisplayName"="@%SystemRoot%\\servicing\\TrustedIn staller.exe,-100"
"ImagePath"=hex(2):25,00,53,00,79,00,73,00,74,00,6 5,00,6d,00,52,00,6f,00,6f,00,\
74,00,25,00,5c,00,73,00,65,00,72,00,76,00,69,00,63 ,00,69,00,6e,00,67,00,5c,\
00,54,00,72,00,75,00,73,00,74,00,65,00,64,00,49,00 ,6e,00,73,00,74,00,61,00,\
6c,00,6c,00,65,00,72,00,2e,00,65,00,78,00,65,00,00 ,00
"Description"="@%SystemRoot%\\servicing\\TrustedIn staller.exe,-101"
"ObjectName"="localSystem"
"ErrorControl"=dword:00000001
"Start"=dword:00000003
"Type"=dword:00000010
"ServiceSidType"=dword:00000001
"FailureActions"=hex:84,03,00,00,00,00,00,00,00,00 ,00,00,03,00,00,00,14,00,00,\
00,01,00,00,00,c0,d4,01,00,01,00,00,00,e0,93,04,00 ,00,00,00,00,00,00,00,00
"BlockTime"=dword:00002a30
"PreshutdownTimeout"=dword:0036ee80
"Group"="ProfSvc_Group"

[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Servic es\TrustedInstaller\Security]
"Security"=hex:01,00,14,90,90,00,00,00,a0,00,00,00 ,14,00,00,00,34,00,00,00,02,\
00,20,00,01,00,00,00,02,c0,18,00,00,00,0c,00,01,02 ,00,00,00,00,00,05,20,00,\
00,00,20,02,00,00,02,00,5c,00,04,00,00,00,00,02,14 ,00,ff,01,0f,00,01,01,00,\
00,00,00,00,05,12,00,00,00,00,00,18,00,ff,01,02,00 ,01,02,00,00,00,00,00,05,\
20,00,00,00,20,02,00,00,00,00,14,00,8d,01,02,00,01 ,01,00,00,00,00,00,05,04,\
00,00,00,00,00,14,00,8d,01,02,00,01,01,00,00,00,00 ,00,05,06,00,00,00,01,02,\
00,00,00,00,00,05,20,00,00,00,20,02,00,00,01,02,00 ,00,00,00,00,05,20,00,00,\
00,20,02,00,00

[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Servic es\TrustedInstaller\Enum]
"0"="Root\\LEGACY_TRUSTEDINSTALLER\\0000"
"Count"=dword:00000001
"NextInstance"=dword:00000001

2. Copy TrustedInstaller.exe from C:\Windows\WinSxS to C:\Windows\servicing,
to do this you have to temporary change the permissions to
C:\Windows\servicing directory. My C:\Windows\WinSxS directory contains three
versions of TrustedInstaller.exe, I taken the middle version.

After this Windows Updates started working and i have installed sp2
successfully


"Trig217" wrote:

>
> Hello,
>
> I am having issues with the error code 80070424. I tried to register
> the dlls as suggested above but when I get to the wudriver.dll it gives
> me the message:
> The module "wudriver.dll" was loaded but the entry-point
> DllRegisterServer was not found.
>
> Make sure that "wudriver.dll" is a valid DLL or OCX file and then try
> again.
>
> I have not found a fix for this and don't know where to turn now.
>
> Please Help.
>
> Thanks!!
>
>
> --
> Trig217
> ------------------------------------------------------------------------
> Trig217's Profile: http://forums.techarena.in/members/trig217.htm
> View this thread: http://forums.techarena.in/windows-update/814712.htm
>
> http://forums.techarena.in
>
>